Motors

Motors (218 Items)

Page
per page
Set Descending Direction
  1. 1 RPM 24VAC TIMING MOTORS

    1 RPM 24VAC TIMING MOTORS

    Synchron K13RC-5-6. 1/8" dia x 3/8" long output shaft. only 1 left.

  2. 24VDC 5 WATT MOTOR

    24VDC 5 WATT MOTOR

    Dec 12-19267 REV.B.. Also Hitachi D04a191E. 3" long x 1.5" diameter. 1/8" diameter x 3/4" long shaft. 4 wire lead. only 1 left.

  3. 5.25" DIAMETER DC PERMANENT MAGNET MOTORS

    5.25" DIAMETER DC PERMANENT MAGNET MOTORS

    Hathaway . 360 DC Permanent Magnet Motors with an overall length of 5.25 inches, diameter of 2.5 inches and a shaft diameter of 5/16ths that were manufactured by Hathaway and designed to operate on 115AC/DC. P.O.R.

  4. MITSUMI 7.5 DEGREE STEPPER MOTOR

    MITSUMI 7.5 DEGREE STEPPER MOTOR

    Mitsumi #M49SP-1, RH7-1320 01. 1.8 ohm. Approximately 1-7/8" diameter x 1-1/8" long. Two mounting ears. Tiny 4-prong male plug. 6000 brand new units available. Offers?

  5. 7,476 ZHONGSHAN E. M. & A GEN-115VDC 60 HZ 0.9A - 15W 1550 RPM CLA TPL 199 # E18093A MOTORS AVAILABLE!

    7,476 ZHONGSHAN E. M. & A GEN-115VDC 60 HZ 0.9A - 15W 1550 RPM CLA TPL 199 # E18093A MOTORS AVAILABLE!

    7,476pcs of Zhongshan E. M. & A Gen-115VDC 60 Hz 0.9A - 15W 1550 RPM CLA TPL 199 # E18093A available. These motors are equivalent to the Grainger exhaust motor #18, or the Fasco # D120. These units are the size of a coffee mug and are counter clockwise rotation. The original FOB factory price is $23.95US per unit. Application for this motor seems to be mostly for bathroom exhaust fans. Offers considered for min. 2,000 lot.

  6. 12VDC LINEAR ACTUATOR

    LINEAR ACTUATOR FOR AUTO DOOR LOCK

    12VDC motor drive actuator for automotive door locks. Nylon plunger moves 0.75". Push or pull, depending on polarity. Includes mounting hardware and a 10" metal extension rod which fits through the hole in the end of the plunger. Overall dimensions of the actuator assembly in retracted state is 8.42" x 2.35" x 1.15". Rubber boot protects against moisture and dust. pigtail leads.

  7. PULSE WIDTH CONVERTER

    DC TO PULSE WIDTH CONVERTER/DC MOTOR CONTROLLER KIT

    Easy to assemble kit - Velleman # k8004. Ideal for accurate control of DC motors, lighting levels and small heaters as well as other applications. The cirtuit converts DC voltage into a series of pulses, the duration of which is directly proportional to the voltage. Minimizes power loss in the control circuit. Overload and short circuit protection. Input Voltage: 2.5 -25 VCD. Maximum output 8-35 Vdc, 6.5 Amps.

  8. SIEMENS BFP405 TRANSISTOR, NPN, SILICON, RF, SMT SOT-323

    SIEMENS BFP405 TRANSISTOR, NPN, SILICON, RF, SMT SOT-323

    SIEMENS BFP405 Transistor, NPN, silicon, RF, SMT SOT-323

  9. STEPPER MOTOR BOOK

    STEPPER MOTOR BOOK

    Determine surplus stepper motor specs using simple easy to build test equipment. Design and build microcontroller-based control systems. (Flow charts and code examples included) Design and build stepper motor driver circuits. Analyze the mechanical characteristics of stepper motor driven devices. This book is full of experiments, circuits and code.

  10. SIEMENS POT CORE B65937-A0000-X022

    SIEMENS POT CORE B65937-A0000-X022

    We have 9500 pieces available. Take the whole lot at .19 each OBO

  11. EPSON STEPPER MOTOR

    EPSON STEPPER MOTOR

    Epson unipolar, 6 lead stepper motor. 0.98" diameter x 0.60" high body. 0.08 (2mm) diameter x 0.39" long shaft. Oval mounting flange has holes on 1.30" centers. 5" long leads.

  12. MAGNETIC HEAD ASSEMBLY WITH STEPPER MOTOR ADJUSTER

    MAGNETIC HEAD ASSEMBLY WITH STEPPER MOTOR ADJUSTER

    1" diameter stepper motor rotates worm gear to raise and lower a magnetic head assembly, probably from an audio or data tape drive. The worm gear part of this device might be useful for other applications. The motor is a 6 wire, unipolar stepper. The travel of the worm gear is about 0.5". Mounted on a metal assembly 3.1" x 3.3."

  13. MERKL KORFF  AC GEAR MOTOR

    175 RPM 115 VAC MERKLE KORFF REVERSIBLE GEAR MOTOR

    Compact yet powerful reversible gearmotor made by MERKLE KORFF. 52.5% duty cycle. Use on displays, rotisseries, mixers, etc. 2.5 mfd capacitor required (not supplied). specs; 175 RPM, 115 volt AC, 22 inch oz. torque, Shaft 5/16" dia x 1 1/2" w/flat, Size 3 3/4" x 2 1/2" x 3 1/2". Removed from used equipment. Weighs 4 lbs.

  14. CANON SA32-T10S1A CASSETTE DRIVE 12VDC MOTOR

    CANON SA32-T10S1A CASSETTE DRIVE 12VDC MOTOR

    This motor is 1-5/16" dia x 1" high. The shaft has a dual belt drive 3/8" dia pulley. Other numbers also appearing on the motor are; CM32-02401 and 5YGF. Made in Japan. Removed from brand new automobile cassette drive mechanisms.

  15. SIEMENS V23012-A2102-B001 RELAY

    SIEMENS RAVA 909, R6U4, 122/2, V23012-A2102-B001 RELAY (UNKNOWN RATING)

    We do not know the ratings. Bears the following markings. RAVA 909, R6U4, 122/2, V23012-A2102-B001. 1-1/8"L x 3/4"W x 3/8"H. Nine pin PC mount. 8,000 available.

  16. ROBBINS & MYERS KP-F330 220VAC MOTOR

    ROBBINS & MYERS 220VAC MOTOR

    ROBBINS & MYERS 220VAC/50Hz 1150RPM motor. 1/20 HP. Single phase. 4" WIRE LEADS - Size; 4-1/2"H X 4"Dia. Flatted shaft 3/4"L x 5/16" dia. Requires 4-440VAC capacitor (not supplied)

  17. ELECTRIC MOTOR CORP ELECTRIC MOTOR CORP 26 RPM 45 VAC GEARMOTOR

    26 RPM 45 VAC GEARMOTOR

    26 RPM 45 VAC GEARMOTOR. Removed from service. Inline parallel shaft gearmotor. Mounting holes are drilled and tapped. Specifications; RPM 26, Voltage 45 VAC, Amps 0.600 (no load), Rotation CW, Duty Int. 4 hole face mount on 1-9/16" x 1-5/8" centers. Shaft 3/16" diam. x 5-1/4" w/ 10-32 threaded end. Overall Size 1-1/4" x 2-1/2" x 4-7/8" weighs 2 lbs.

  18. EMERGENCY 1200 WATT POWER FOR YOUR SUMP PUMP

    EMERGENCY 1200 WATT POWER FOR YOUR SUMP PUMP

    A power failure, your sump pump dies and disaster is around the corner. This high quality, industrial grade 1200 watt emergency power supply kiks in during a power failure and keeps your pump working for up to 6 hours. Click MORE INFO for Full spec in PDF format. We also have higher power units - inquire. Call Ted at 514-739-8723. Very special prices for quantity purchase.

  19. GEARBOX 2 IN 1,MOTOR

    GEARBOX 2 IN 1, MOTOR GEARS & ACCESSORIES

    Fun with gears and motors. Small 3VDC motor, metal bracket and axles, and an assortment of small plastic gears and collars to produce a gear train of various ratios. Includes; 3VDC motor, metal shafts, spur gear, double spur gear, face gear and pinion gear. Operates on 2 AA batteries (not included).

  20. ORIENTAL MOTORS PARTS & MOTORS

    ORIENTAL MOTORS PARTS & MOTORS

    ORIENTAL MOTORS PARTS & MOTORS: AC Motors & Gearmotors,| AC and Brushless DC Speed Control Systems, Stepping Motors, Electric Linear and Rotary Actuators.

  21. START YOUR OWN ELECTRIC MOTOR BUSINESS ON THIS PAGE

    START YOUR OWN ELECTRIC MOTOR BUSINESS ON THIS PAGE

    Yes - we can help you start your own AC & DC electric motor, parts & equipment business. You can start your business on this very page and get customer inquiries that will lead to solid sales. Get started today. For further information please call Ted at 514-739-8723.