Test Equipment

Click on MORE INFO to view this list of excess test equipment that we have available. Manufacturers such as Hioki, Tektronik, Yokogawa, and many others

Never used, comes with all the original accessories and traveling carrying case. Ideal from maintaining and testing ISDN BRI and PRI networks. Additional pictures available upon request. Send in your offers for this Frederick engineering ParaScope 2000 ISDN tester today.

ZELLWEGER ANALYTICS, toxic gas continous monitor, unused condition, still in original box. Model SPM Z-PURGE. PART NO 870850, 115V/60HZ/0.2A, Complete with explosion proof switch, purge gas inlet regulator, teflon tubing and operating manual. Housed in rugged NEMA 4X fiberglass enclosure. Unit is programmed for Hydrazine detection but is programmable for a long list of other gases. Click on MORE INFO to see photo in pdf format.7 available.

Glassbreak simulator testers by Ademco Honeywell, Intellisense FG-701. Over 100 units available.

Scientific test equipment and test equipment parts by Kodak, Lambda, Motorola, Newport Research Corp, Omni-Spectra and many more. Click "more info" for complete list of inventory available.

Compact and light, this multimeter has a large, 3.5 digit 7-segment, half-inch high LCD display. Max. reading of 1999. Measures DVC (0,1mV - 1000V), ACV (0,1V - 750V), DCA (0,1mA - 10A), Ohm (0,1 - 2M) diode forward voltage drop & hFE for bi-polar PNP and NPN transistors. Overall size: 126mm x 68mm x 24mm. Power source: 9V battery. Has low battery indication and comes with tester cable.

Control two unipolar step motors via the parallel port. Kit includes much more than shown, such as four ditigal inputs, DOS based program on diskette complete with C source code, and an extended D-shell plastic case.

Used to vary the speed of DC motors, circuit delivers voltage to motor with pulses and speed is controlled via pulse width modulation. Speed control is a potentiometer for DC motors up to 100 volts at max. 5 amps.

Measurement Computing Corp. miniLAB 2008 I/O modules. Two units.

HDMI cable tester is compatible with all HDMI & DVI cables, and is useful when the cable is installed inside a wall between rooms. Features red LEDs, test HDMI, DVI cables, 9V DC battery powered transmitter and gold-plated HDMI jacks. 9V battery not incl.

4-Pair-EIA/TIA568/coaxial cable tester tests installed or local cable with removable RJ45-BNC remote unit. Provides instant diagnosis of 4-pair twisted-pair and coax for continuity, opens, shorts, miswires, crossed, reversed, transposed and split-pairs. 9V battery incl.

Lecroy 6030A Waverunner oscilloscope 4-channel, 350MHz, 2.5/5 GS/s 4/8 Mpts Standard, Microsoft Windows XP Pro based color DSO with options: ZS1500-QUADPAK/WR6-L. 1 available.

Includes digital oscilloscope, digital function generator and easy-to-use power supply. The three units are electrically separated for ease of measurement. Click "more info" for complete specs.

Connect multiple solar panels and inverters safely and quickly with this handy solar accessor kit. Includes: voltage tester w/LED, 12 V DC plug, female socket connector, barrel connector, battery clamps and an extra 12 feet of wire.

The Hach model LDO-HQ10 luminescent oxygen meter measures dissolved oxygen only. Inputs: (1) 5-pin Hach dissolved oxygen probe locking connector. Outputs: RS232 via Docking Station. Enclosure: Waterproof (designed to meet IP67), chemical-resistant, dust proof; meter will float. DISSOLVED OXYGEN MODE: Range 0 to 20 mg/L (ppm), 0 to 200% saturation Accuracy: +/-0.1mg/L for 0-8 mg/L; +/- 0.2 mg/L for greater than 8-20 mg/L. ***DOES NOT INCLUDE dissolved oxygen probe which has been discontinued by Hach. 2 available.

This HDMI remote cable tester allows pre-testing of any standard HDMI 1.2v or 1.3v cables at the rough wire stage of installing, and again after the cable is installed. Can also be used to test DVA cables by using a DVA to HDMI adapter.

Designed to quickly test and troubleshoot standard HDMI 1.2v and 1.3v cables. Intended for in-store use in assuring all internal cable connections are wired correctly. Using a DVI to HDMI adapter, it can be used to test DVI cable assemblies as well.

The Beacon 100 is a continuous-monitoring instrument capable of detecting gas and continuously displaying the gas reading on it's screen. Audible and visual alarms warn of hazardous gas conditions.

Digital bench multimeter features automatic or manual range selection (32 ranges), digital and analog 3 3/4 display, 3999 counts & 43-segment bargraph, digit height 0.7". Data-hold, max/min & relative measurements, display/recall of stored data, true rms for AC voltage & current, continuity & diode test, RS-232C standard interface and a backlight. Adp measurement: 400mV ± 0.3%, 10 digits/1mVdc. Software compatible with Win95 and 98. Power source: AC or DC power supply (power cable included).

3-3/4 digit mini clamp-on amp meter features a digital & analog backlit LCD display, 42-segment fast analog bar graph, display & audio continuity test, diode test, auto power off, auto & manual range and data hold. Comes with 18" test leads, AAA batteries, black carrying case and dust-proof wrist strap.

Non-contact inductive voltage detector can sense 100-240VAC within 2" range and emits flashing light and audible tone. Two AAA batteries incl.

Digital tachometer gives accurate RPM measurements in exact RPMs on a 5-digit LCD display. Has 2 test modes: RPM and REV. Last value & max/min RPM values are stored automatically. Power supply: 1 x 9V 6LR61 battery (incl) or external power adapter 6-9VDC (not incl). Comes with carrying case.

Digital thermo- & hygrometer with large LCD display records maximum & minimum temps and humidity in °C or °F. Features low battery indication and has table stand or wall mount. Specs: Temperature range: * indoor: 32°F~122°F * outdoor: -4°F~167°F - hygrometer: indoor humidity only - power supply: 1 x 1.5V AAA battery (LR03C, not incl.) - dimensions: 4 39/64" x 4 7/32" x 25/32"

This palm-sized anemometer comes with a neckband for easy carrying in the field. Features wind speed measurements: in mph, km/h or m/s units (min. 0.2m/sec - max. 30m/sec), shows wind speed in Beauford wind scale bar graph, has a wind chill display in ºC or ºF, a data-hold function, auto power 'off' and LCD backlight. power supply: 1 3V CR2032 battery (incl.), dimensions: 1.5" x .7" x 3.9"