Designed to meet exacting Xerox standards, this Buehler beauty is a powerhouse... produces 80Ncm torque with only 0.68 - 0.83A draw at 77 - 94Rpm - or 114-133rpm @ 20Ncm torque with only 0.195 - 0.290A draw. Can be used
bi-directionally. Full drawing and specs available - click the "more info" icon.
$49.95 Ea/2, $39.95 Ea/5.
6 in stock
TS194
|
25VDC operation. Produced originally for use by Xerox, this 2.7" (overall length) gearmotor features a semi-flat shaft for ease of adaptation to your specific requirments. 80rpm no load speed with only 140ma current draw. At
31Ncm, speed is 74rpm and drain is a low 500ma. Click the "more info" icon for full specs and drawing.
$29.95 Ea/3, $24.95 Ea/5.
18 in stock
TS195
|
24VDC gearmotor is 2.7" long (not including shaft, which is .9" long or gearhead 0.75"). Gear ratio is 30:1. Bi-directional operation. At 50Ncm torque, speed is 180rpm and current drain 830ma. Full specs and drawing
available - click the "more info" icon.
$25.95 Ea/4, $19.95 Ea/8.
19 in stock
TS196
|
|
High performance Buehler model 16104615500 12VDC gearmotor. Draws only 650MA at a load of 7Ncm and operates at 330rpm. Shaft is 0.20" diam x 0.37" long semiflat. Can be used bi-directionally. No load speed is 490rpm. Click
the "more info" icon for full specs and drawing!
$29.95 Ea/3, $19.95 Ea/6, $17.95 Ea/12, $16.95 Ea/24.
340 in stock
TS197
|
|
12VDC operation. Buehler model 16104615600. Heavy duty, 2.5" length, 1.3" diameter gearmotor features a semiflat shaft (approx 1/8" dia x 1/2" length) and bi-directional operation. At a load of 20Ncm, speed
is 106rpm and current drain is 650ma. Full drawing and specs - click the "more info" icon.
$19.95 Ea/5, $17.95 Ea/10, $16.95 Ea/25, $12.95 Ea/100.
457 in stock
TS198
|
|
12VDC - 30NCM TORQUE GEARMOTOR
|
Excellent for modellers, robotics, small electric vehicle experiments, etc. Great Buehler model 16104615700 12VDC gearmotor is 2.8" long x 1.4" diameter. Shaft is 0.20" semiflat x 0.5" length. Bi-directional
operation. At 12vdc, 390ma, speed is 42rpm and torque is 30Ncm. For full specs,. click the "more info" icon.
$39.95 Ea/2, $24.95 Ea/12, $17.95 Ea/24, $14.95 Ea/96.
27 in stock
TS199
|
Compact gearmotor is only 2.4" long x 1.4" dia. Shaft is semiflat, 0.20" dia x 0.40" length. Under load (4.2Ncm) speed is 715rpm, current drain is 0.75A @ 13vdc. This is a great motor for modellers, robotics,
science projects, etc. Bi-directional operation. Full drawing and specs - click the "more info" icon.
$14.95 Ea/6, $12.95 Ea/12, $11.95 Ea/24, $9.95 Ea/96.
1198 in stock
TS201
|
GEAR MOTOR WITH WORM REDUCTION
|
Originally manufactured for use by Xerox, this gear motor with worm reduction produces a shaft speed of 240 - 268rpm under load (54Ncm) with a current drain of only 1.285 A. Click the "more info" icon for full specs and
drawing.
$29.95 Ea/3, $24.95 Ea/10, $19.95 Ea/50.
207 in stock
TS193
|
|
Compact gearmotor is only 2.4" long x 1.4" dia. Shaft is semiflat, 0.20" dia x 0.40" length. Under load (4.2Ncm) speed is 715rpm, current drain is 0.75A @ 13vdc. Bi-directional operation. This is a great motor
for modellers, robotics, science projects, etc. Full drawing and specs - click the "more info" icon.
$14.95 Ea/6, $12.95 Ea/12, $11.95 Ea/24, $9.95 Ea/96.
210 in stock
TS200
|
Click the graphic to visit ONLYBATTERIES.COM
TS795
|
SURPLUSTRADERS.NET can solve your problem!
SURPLUSTRADERS.NET now offers a superior sourcing service for use by corporate clients with major purchase (in excess of $50,000US) requirements. We do the leg-work for you, find a
viable vendor, then put you in direct contact with the vendor.
We operate on flat rate basis which takes into account the complexity and dollar value of the products you require.
This service is offered to our corporate clientele only and each
requirement is analyzed before a fee-for-service quote is rendered.
For more information, please contact:
Ted Duskes, 1-800-341-6468 (ted@surplustraders.net)
or
Marshall Duskes 1-866-266-7638 (marshall@surplustraders.net)
TS789
|
Right angle surplus motors by Buehler, p/n 1.13.022.212.03, with worm gear that drives two plastic spur gears. 12VDC, 69 mA @ no load, 48 RPM. Continuous duty, reversible rotation. Overall dimensions: 5-7/8" x
1-5/8" x 2-3/4" with 0.33" diam. x 0.33" long shaft. Two tapped holes on 1.658" centers mount.
New
GF956
Parallel shaft gearmotor by Merkle-Korff. 9VDC, 0.23 amps @ no load, 62 RPM. Reversible rotation, intermittent duty and gear ratio of 46.1:1. Die-cast gear housing. Dimensions: 3-1/4" x 2-1/2" x
3-5/8" with 5/16" dia. x 7/8" w/flat & snap-ring groove. Mount: Six thru-holes on 2-1/16" x 1-23/32" centers or 2-1/16" x 2-29/32" centers. Holes are for #8 thread forming screws.
New
GF955
CKD model J209-056 24VDC synchronous gearmotor comes attached to removable mounting bracket. 15 RPM, 0.2 amps no load. Intermittent duty, CW rotation. Dimensions: 4" x 1-3/4" x 2" with 3/16" dia. x
1/2" long shaft w/ flat shaft. 2 bolt mount on 3-13/32" B.C.
New
GF844
30 RPM, 24VDC high-torque gearmotor w/offset gearbox. By Multi-Products Co. Inc., model 2738. 0.68 amps no load, 47 in. lbs. torque. Continuous duty, reversible rotation. Dimensions: 4-1/2" x 3" x 4-3/4"
with 11 mm diam. x 12 mm w/dual flats shaft. Mount: 4 bolt 2-1/2" x 2" pattern.
New
GF843
24VDC permanent magnet gearmotor by Molon, model CHM-2435-1. Has 4-7/8 inch wheel with o-ring on edge to be used as drive wheel for robots. 45 RPM, 0.28 amps, continuous duty, reversible rotation. Operates at half-speed on
12VDC. Torque: 7.5 in-lbs. Dimensions: 2-3/4" x 2-1/4" x 3" with 5/16" diameter shaft. Mount: 4 tapped holes 2-3/8" x 2-1/2".
New
GF842
12 VDC motor and gear assembly. 1.8 amps, 104 RPM. Plastic gears & housing with fixed center hub with opening for 3/8" axle. Gear ratio is 194.8:1, rotation reversible, duty continuous. Open enclosure.
Dimensions: 3-1/4" x 6-15/16" x 3-3/4", shaft: 2-1/4" dia. 6 tooth, female.
New
GF805
165 electric and 1 hydraulic motor by Toshiba, GE, Siemens and more. AC & DC, 10HP to 1250HP. Click "more info" for complete list.
GF669
Pittman GM8712G416-R2. Exceptional value - excellent for RC applications, robotics, automotive applications, etc. Superb quality Pittman motor features a 922.5:1 gear reduction ratio. Units are brand new, and fully guaranteed.
Specs, as supplied by one of our clients:
Output shaft - 1/8" diameter x 5/16" long, No load RPM @ 12VDC: ~8.1RPM, No load current @ 12VDC: ~325ma, No load RPM @ 6VDC: ~ 3.75RPM, No load
current @ 6VDC: ~250ma
Normal distribution channel pricing for this motor is as high as $87. Click the more info button for a PDF file on similar (not exact) Pittman motors to view typical quality and performance for this style of motor.
Click the picture for a larger photo.
$21.95 Ea/5, $19.95 Ea/10, $17.95 Ea/20, $15.95 Ea/50.
178 in stock
TS081
|
As pictured. The 12VDC motor is Merkle-Korff Industries. The motor is approx 1-1/2" dia. x approx 2-3/8"L. The gearbox is approx 5-1/2" L x approx 1" thick x approx 3" W. The clutch mechanisim as
pictured is 3" dia. x approx 1-3/4" thick. The clutch and motor each have two wires. Inventory shipped may vary slightly from this description as the inventory may be mixed but units will be similar. Little else is known about this assembly.
Removed from used equipment. Good condition.
$79.00 Ea.
52 in stock
MD206
Permanent magnet, 500 RPM 12 VDC right angle gearmotor. Cast aluminum gear housing with steel motor frame. Hollow square thru-drive output shaft and two bolt rubber isolation mount. Specs: Speed 500 RPM no load, 250 RPM at
rated torque. Voltage 12 DC. Rotation Reversible. Duty Intermittent, enclosure TENV. Amperage 16 Amps. Torque 8.5 in-lbs. Mount 3/8" dia. two bolt on 2.2"centers, hollow thru-shaft 5/32" (4 mm). Dimensions: 5-1/4" x
3-1/8" x 2-1/2".
New
GE299
Buehler 12VDC/21RPM 90 Deg. angled gearhead DC motor, p/n 1.61.031.119.00. Has 5VDC, TTL compatable, 50Pulse/RPM Tach. mounted on rear. Rated: 10/21/42RPM @ 6/12/24VDC, 300mA No Load/4.5A
Stall @ 12V. 4ft/lb Stall torque @ 12V. 8mm dia. X 50mm removable/reversable steel shaft held in place by a collet. Removable sheet metal mtg. bracket. 5" Tach leads, 8" motor leads. Dimension: L: 8-1/2" (OA) W:
4-1/4" H: 3".
Used
GE245
Copal LC37G-183 12VDC gearhead motor. 27mm flatted steel shaft with metal gears. 3 corner mounting mounting holes. 5" leads. 110RPM @ 12V or 220RPM @ 24V. 6mm dia. 1-7/8" X 1-5/8" mounting flange.
Dimension: L: 2" (Body) Dia: 1-15/16".
New/pulled
GE240
RP2020 1.6 RPM, 12VDC inline gearmotors. Ideal replacement corn pellet stove, auger motor. Aluminum gear housing. Six 10-32 bolt hole face mount on 1-15/16" - 4-3/8" x 2-3/8" centers. Amperage 350 mA, torque
78 in - lbs., rotation reversible. Duty continuous, enclosure open. Shaft 3/8" diam. x 1" w/flat. Overall size 3-3/4" x 2-3/4" x 4-3/4".
New
GE225
|
|
S..L..O..W.. 28RPM MOTOR!
|
Source Engineering 35DB30-1250/37G150. High quality, compact (34.4mm dia) 12vdc gearhead motor produces 18kg-cm torque @ 27RPM with only 330ma current drain. CCW rotation. Flatted shaft. Click the "more info" icon
for the full spec sheet / drawing.
$11.50 Ea/12, $10.50 Ea/24, $8.50 Ea/48, $7.50 Ea/96.
413 in stock
TS543
|
Buehler motor and gearhead attached to a cam and crank. The crank has a throw of 1.5". In addition to the moving the crank, the cam trips a SPDT micro type switch (rated 0.1A / 125Vac) twice for each revolution. The
assembly is attached to a 3.22" x 2.42" metal frame with mounting ears. The parts are easily removable. The Buehler motor is approximately 1.38" diameter x 2.80" long. 21 RPM at 6VDC and 42 RPM at 12VDC. A great experimenters or scholl
project item.
$49.95 Ea, $44.35 Ea/5.
MG412
Here is a tutorial that explains in simple "baby talk" how little DC electric motors work. Take a few minutes to read it over, and enjoy learning what makes them spin. A little knowledge goes a long way and can serve you
well if you work in the world of motors. Enjoy! 
MG043
|
Sayama. Compact, good-quality 12VDC gearhead motor. 58RPM, @ 12VDC, 20mA (no-load). 12mm diameter x 35mm long. Solder-lug terminals. 2mm diameter x 6mm long flatted shaft.
$27.85 Ea/5.
MF949
FoMoCo Ford Explorer. 130 RPM @ 12VDC/860MA, no-load rating. Final drive shaft is 0.27" diameter x 0.32" long with an easily removable 0.54" diameter gear. Overall dimensions, 6.38" x 3.78" x 1.65".
Gearbox has two mounting holes on 3.10" centers. Gearbox case has a plastic cover containing a pc board which must be removed to make the motor useful for non-Ford applications. Please click pic to enlarge.
$28.85 Ea/5.
MF863
Marked CB2D. This gear motor will operate over the range of 6 to 24 VDC. At 12VDC it delivers 6.8 RPM. At 24VDC it delivers 14.6RPM. The motor is 1-1/4" dia. x 2-11/16" long. The flatted shaft is 3/16" dia.
x 3/8" long. The overall length of the assembly is 2-1/2". Diameter of the gearhead is 1-1/4" Motor terminals are .110"
$24.85 Ea/5.
MF214
Fun with gears and motors. Small 3VDC motor, metal bracket and axles, and an assortment of small plastic gears and collars to produce a gear train of various ratios. Includes; 3VDC motor, metal shafts, spur gear, double spur
gear, face gear and pinion gear. Operates on 2 AA batteries (not included).
$14.95 Ea, $12.45 Ea/10.
ME689
We have been offered the following brand new motors; HURST: 3 each of (PCDA) 990535, 2 each of (PC) 990525, 2 each of (PCDA) 990513, MAXON: 3 each of 118783. I am accepting offers for this lot. Ted 514-739-8723
ME573
Rugged 5 RPM 12VDC gear motor designed to move baffles in automobile air conditioning. Great for continuous or intermittent use where power, slow rotation, low noise and low current are desired. Mechanism consists of a small DC
motor with a worm gear driving a four gear train. Final drive is a plastic splined shaft, 0.52" diameter x 0.5" long. The composite plastic housing is easily opened for access to the motor, gears and electrical terminals. Overall dimensions of
assembly including mounting flanges and shaft is approximately 3.12" x 4.25" x 1.62." No load measurements: 5 RPM @ 13.5 Vdc @ 15 mA.
$19.00 Ea/5.
ME512
|
Pittman GM8712G416-R3. Exceptional value - excellent for RC applications, robotics, automotive applications, etc. Superb quality Pittman motor features a 922.5:1 gear reduction ratio. Units are brand new, and fully guaranteed.
Normal distribution channel pricing for this motor is as high as $87. Click the more info button for a PDF file on similar (not exact) Pittman motors to view typical quality and performnce for this style of motor. Click the picture for a larger photo.
$24.95 Ea/5, $19.95 Ea/10, $17.95 Ea/20, $15.95 Ea/50.
199 in stock
TS063
|
Powerful little 6-12 VDC gearhead motor. 2.43" long, excluding shaft. 1.3" diameter x 1.15" long gearbox. Flatted 0.2" diameter x 0.39" long offset shaft. Three tapped mounting holes on motor face. No-load
ratings: 3 RPM, 6 VDC, 75 mA. 6 RPM, 12 Vdc, 85 MA.
$27.80 Ea/5.
MD979
|
CCL Motor DE-25L . This very unusual motor has been prepped with a full wave bridge rectifier for use on 125VAC. If you bypass the bridge rectifier it works very nicely on any DC power from 12VDC on up. The final drive is a
0.8" long worm gear that turns a 0.8" dia. plastic gear at 120RPM @ 12VDC (no load). Replaceable brushes. Motor body is 1.41" dia. x 2.75" long. Contcat Ted Duskes at 514-739-8723 for quantity purchases!
$3.95 Ea, $2.49 Ea/100, $2.29 Ea/500, $1.95 Ea/1000.
2 in stock
TH195
|
|
